2016 Honda CR-V

  • 2016 Honda CR-V

    Honda CR-V
    Mileage
    47,847
    Service Date
    8/14/2024
    Services Performed
    • Comprehensive Digital visual inspection, road test, auto scan.
    • Engine oil and filter replacement with full synthetic 0w20 Idemitsu O.E.
    • VALVE CLEARANCE – ADJUST – [Adjust only if noisy.] MAINTENANCE MINDER LIGHT – RESET – [Reset the Maintenance Minder Light after every service is performed. If the Light is reset without performing a service, the system will not show the proper maintenance intervals. This can lead to serious mechanical problems because you will no longer have an accurate record of when maintenance is needed.] TIRES – ROTATE
    • VALVE CLEARANCE – ADJUST – [Adjust only if noisy.] AUTOMATIC TRANSAXLE FLUID – INSPECT BRAKE FLUID LEVEL – INSPECT BRAKE HOSES & LINES – INSPECT – [Check the master cylinder and ABS/VSA modulator-control unit for damage and leakage.] DRIVESHAFT/PROPELLER SHAFT DUST BOOTS – INSPECT – [Check boots for cracks and boot bands for tightness.] ENGINE COOLANT – INSPECT – [Check the coolant level in the coolant reservoir. Make sure it is between the MAX mark (A) and the MIN mark. If the coolant level in the coolant reservoir is at or below the MIN mark, add coolant to bring it up to the MAX mark, then inspect the cooling system for leaks.] EXHAUST SYSTEM – INSPECT – [Check catalytic converter heat shields, exhaust pipes, and muffler for damage, leaks, and tightness. NOTE: According to state and federal regulations, failure to do this maintenance item will not void the customer's emissions warranties. However, Honda recommends that all maintenance services be done at the recommended interval, to ensure long-term reliability.] FRONT BRAKE SYSTEM – INSPECT – [Check pads and discs for wear (thickness), damage, and cracks. Check calipers for damage, leaks, and tightness of mounting bolts.] FUEL LINES & CONNECTIONS – INSPECT – [Check for loose connections, cracks, and deterioration; retighten loose connections and replace damaged parts. NOTE: According to state and federal regulations, failure to do this maintenance item will not void the customer's emissions warranties. However, Honda recommends that all maintenance services be done at the recommended interval, to ensure long-term reliability.] PARKING BRAKE – INSPECT POWER STEERING FLUID – INSPECT – [Check the reservoir at regular intervals, and add the recommended fluid as necessary. Always use Honda Power Steering Fluid. Using any other type of power steering fluid or automatic transmission fluid can cause increased wear, fluid leaks, and poor steering in cold weather. NOTE: If the fluid is contaminated, the screen in the reservoir may be partially clogged. Inspect the reservoir screen for any debris. If the reservoir screen is clogged, replace the reservoir, and check for the source of the contamination.] REAR AXLE FLUID – INSPECT REAR BRAKE SYSTEM – INSPECT – [Check pads and discs for wear (thickness), damage, and cracks. Check calipers for damage, leaks, and tightness of mounting bolts.] STEERING GEAR/RACK – INSPECT – [Check steering linkage. Check fluid lines for damage or leaks.] STEERING RACK BOOTS – INSPECT – [Check boots for damage and leaking grease. Check fluid lines for damage or leaks.] SUSPENSION COMPONENTS – INSPECT – [Check bolts for tightness. Check condition of ball joint boots for deterioration and damage] TIE ROD ENDS – INSPECT WINDOW WASHER FLUID LEVEL – INSPECT ENGINE OIL – REPLACE ENGINE OIL FILTER – REPLACE MAINTENANCE MINDER LIGHT – RESET – [Reset the Maintenance Minder Light after every service is performed. If the Light is reset without performing a service, the system will not show the proper maintenance intervals. This can lead to serious mechanical problems because you will no longer have an accurate record of when maintenance is needed.]
    • CONTROL ARM – Remove & Replace – Lower,Both – [DOES NOT include alignment.]
    • Replace front brake pads with heat resistant ceramic pads, machine front brake rotors, clean assembly, clean and grease slider pins. Torque all bolts to factory specs and mark. Quality control and road test.
    • Repla
     
    Bob H. gave our service a 5 star review on 8/15/2024

Address

MESMAN MOTORS
24002 Via Fabricante #509
Mission Viejo, CA92691
(949) 580-0700

We Service